Rosslare AC-225? AC-225IP? AC-225U Guia do Utilizador Página 1

AC-225 Advanced Scalable Networked Access Controller Hardware Installation and User Guide July 2007

Technical Specifications AC-225 Hardware Installation and User Guide Page 9 Power Supply Specifications Input Voltage 16V AC / 2.5A From Transforme

AC-225 Panel Set-Up 3. AC-225 Panel Set-Up Every AC-225 panel controls one or two doors. The panels connect together in a network and are controlled

AC-225 Panel Set-Up 3.1 Inputs Wiring – Non-Supervised Inputs Figure 3: Inputs Wiring – Non-supervised Inputs 3.2 Inputs Wiring – Supervised Input

AC-225 Panel Set-Up 3.3 Outputs Wiring The following diagram illustrates wiring for two main types of 12VDC electrical release mechanisms. Other ele

AC-225 Panel Set-Up AC-225 Hardware Installation and User Guide Page 13 3.4 Power Supply The following diagram illustrates wiring between the PS-14

AC-225 Panel Set-Up Figure 6: Wiring Between PS-14 and AC-225 AC-225 Hardware Installation and User Guide Page 14

AC-225 Panel Set-Up 3.5 Reader Proximity & keypad readers are supplied with a limited cable. The color of the cable cover represents the cable’s

Input and Output Requirements AC-225 Hardware Installation and User Guide Page 16 4. Input and Output Requirements This chapter describes the AC-22

Input and Output Requirements Normally Open Input Connection: Normally Open Input has 2 states: • Switch Open - Normal State: Loop resistance = Infi

Input and Output Requirements Normally Closed Input Connection: Normally Closed Input has two states: • Switch Closed - Normal State: Loop resistance

Input and Output Requirements Normally Open Supervised Single Resistor Input Connection Connect an 8.2K resistor in parallel to the input switch conta

Input and Output Requirements Normally Open Supervised Double Resistor Input Connection Connect a 2.2K resistor in series to the input switch contacts

Input and Output Requirements Normally Closed Supervised Single Resistor Input Connection Connect a 2.2K resistor in series to the input switch contac

Input and Output Requirements • Open circuit (Infinite loop resistance) or short circuit (0 resistance) across input terminals - Trouble State. Figu

Input and Output Requirements Door Monitor Input The Door Monitor Input typically connects to a Normally Closed door sensing micro-switch for door sta

Input and Output Requirements General Purpose Inputs These are free inputs that can be used for various functions. The following should be defined: S

Input and Output Requirements Note: The user can select either "Normally Open" or "Normally Closed" output contacts. The followi

Input and Output Requirements AC-225 Hardware Installation and User Guide Page 26 Single door controller: Door 1 – Reader 1 IN/OUT Door 1 – Reader

AC-225 Hardware Settings AC-225 Hardware Installation and User Guide Page 27 5. AC-225 Hardware Settings Each AC-225 panel controls an entrance. The

AC-225 Hardware Settings 5.1 DIP Switch Configuration The access control panel DIP switch controls a number of operating parameters including the dev

Table of Contents AC-225 Hardware Installation and User Guide Page ii Table of Contents 1. Introduction...

AC-225 Hardware Settings 1 2 3 4 5 6 7 8 Figure 15: DIP Switch with Baud Rate Setting The following lists switch 1 and 2 status and baud r

AC-225 Hardware Settings Single Door Controller This access type has two readers, IN and OUT, as follows: Outputs Door lock strike General purpose

AC-225 Hardware Settings 1 2 3 4 5 6 7 8 Figure 17: DIP Switch with Internal Network Address Setting Note: For successful communications, t

AC-225 Hardware Settings AC-225 Hardware Installation and User Guide Page 32 18 On Off Off Off On 19 On Off Off On Off 20 On Off Off On On 21

Communications 6. Communications Communication lines are used to upload and download information between the access control panel and the VeriTrax AS

Communications RS-232 Connection to the Computer Set the J1 switch to the RS-232 position. Access control panel DB9 Connector DB25 Connector GND Pin

Communications Daisy Chaining Daisy chaining allows many panels to connect to the computer along a single serial line. The first panel is connected di

Communications 6.2 TCP/IP Network Connection The computer running the VeriTrax AS-225 software can communicate with the access control panels via a T

Communications RS-232 MD-N32 Access Control Panel LAN/WAN Figure 19: MD-N32 Configuration connecting a single panel When using an MD-N32, for a singl

Communications 6.3 Modem Network Connection Access control panels can be controlled from the computer's modem. The modem is assigned from within

Introduction AC-225 Hardware Installation and User Guide Page 3 1. Introduction AC-225, AC-225IP and AC-225U access control panels are state-of-the-

Communications Prerequisites Before performing permanent modem installations, the modem that will be connected to the panel must be initialized from

Limited Warranty AC-225 Hardware Installation and User Guide Page 40 Appendix A. Limited Warranty ROSSLARE ENTERPRISES LIMITED S (Rosslare) TWO YE

Limited Warranty AC-225 Hardware Installation and User Guide Page 41 Exclusions and Limitations ROSSLARE shall not be responsible or liable for any

Technical Support AC-225 Hardware Installation and User Guide Page 42 Appendix B. Technical Support Asia Pacific, Middle East, Africa Rosslare Secu

0706-0960202+00 www.rosslaresecurity.com

Introduction Figure 1 AC-225 panel AC-225 Hardware Installation and User Guide Page 4

Introduction 1.1 Features The AC-225 is a powerful and adaptable access control solution with a range of powerful features. • Controls 1 or 2 doors

Introduction AC-225 Hardware Installation and User Guide Page 6 Client-Server Structure VeriTrax AS-225 operates through a dedicated VeriTrax server

Technical Specifications AC-225 Hardware Installation and User Guide Page 7 2. Technical Specifications Electrical Characteristics Operating Voltage

Technical Specifications AC-225 Hardware Installation and User Guide Page 8 Communication Characteristics RS-232 Terminal Block RS-485 Molex and T